Course & Cost

TDM20207 Certificate II in Transport and Distribution
(Marine Engine Driver – Grade 3)

Cost

$1320.00, 6 days.

A discount may apply for Skills Recognition (RPL).

Training Units

The TDM20207 Certificate II in Transport and Distribution (Marine Engine Driver – Grade 3) qualification course is nationally recognised by maritime authorities in all States of Australia and selected countries internationally. Sixteen (16) training units are required for the completion of the TDM20307 qualification. The first three (3) units are delivered and assessed at the TDM10107 Certificate I General Purpose Hand course. A further thirteen (13) units are delivered over six (6) days.

Unit CodeUnit of Competency
GPH Units 1 to 3 Refer to TDM10107 Certificate I General Purpose Hand
1 TDMME1107A Contribute to effective communications and teamwork on a coastal vessel
2 TDMMF1107B Survive at sea in the event of vessel abandonment
3 HLTFA301B Apply first aid: external course
Part 1 Units 4 to 8 TDM20207 Certificate II Marine Engine Driver
4 TDMMF5407A Observe safety and emergency procedures on a coastal vessel
5 TDMMF5507A Fight and extinguish fires on board a coastal vessel
6 TDMMR5407B Carry out refuelling and fuel transfer operations
7 TDMMU507B Ensure compliance with environmental considerations in a small domestic vessel
8 TDMMR1907B Safely handle & stow explosive & flammable materials
Part 2 Units 9 to 16 TDM20207 Certificate II Marine Engine Driver
Engineering Week, 5 days
9 TDMMR3007B Operate and carry out basic service checks on small vessel marine propulsion system
10 TDMMR3107B Operate and carry out basic servicing on auxilliary systems
11 TDMMR3207B Operate and carry out basic routine servicing of marine extra low and low voltage electrical systems
12 TDMMR6107A Use and care for hand and power tools on a small vessel
13 TDMMB3607B Prepare small vessel's machinery for sea within the limits of responsibility of a MED 3
14 TDMMR1807B Operate deck machinery installed on a small vessel of less than 750 Kw propulsion
15 TDMMB1907B Carry out basic hull servicing
16 TDFMMF3907B Maintain running log within the limits of responsibility of a MED 3

Course Content

Engineering Week, 6 days
Time:8.45am to 4.00pm
  • Complete SEA SCHOOL enrolment, attendance, provide identification and current 'Apply First Aid' statement of attainment or similar (if already a holder)
  • Introduction to SEA SCHOOL, fellow participants, safety orientation, distribution of Handbooks
  • Commencement of trainer led presentation
  • Identify and observe hazards, emergency alarms, and ways to control damage on board.
  • Know the classes of fire and extinguishing agents to respond to a fire or other emergencies.
  • Fixed fire suppression systems, SCBA self contained breathing apparatus.
  • Plan and prepare refuelling and fuel transfer operations for outboard and diesel engines.
  • Apply relevant local environmental legislative requirements.
  • Stow explosive, flammable and hazardous materials
  • How to operate portable fire fighting equipment. Water, CO2, Dry Chemical Powder, Foam and Fire Blanket.
  • How to use the oil containment unit; and wharf sullage for waste or water.
  • Understand how your engines work.
  • Basic engineering presentation, through hull fittings.
  • Piston assemblies, crankshafts and cooling systems.
  • Engine troubleshooting, identifying defects and faults.
  • Marine extra low and low voltage electrical systems, batteries and shore power.
  • Hull integrity, through hull fittings, condition and seaworthiness of a vessel.
  • Follow safety and hazard control procedures.
  • Basic hull servicing.
  • Prepare a small engine for sea, pre-departure and shut down engine checklists.
  • Operate and maintain deck machinery, manual and hydraulic.
  • Critical planning, maintain a running log, engine hours and fuel calculations.
  • Presentations on the use of hand tools and operation of power tools.
  • Complete the assessment tasks, worksheets, written assessments, multiple choice questions and trainer feedback.
  • Ensure written assessments are received
  • How to get your sea service approved and types of evidence required.
  • How to complete and lodge your NSW Maritime Application for oral assessment to gain your Marine Engine Driver Grade 3 Certificate of Competency.
  • Complete 'Your Opinion Counts' feedback form.

Required Reading

  • Every participant of the TDM20207 Certificate II Marine Engine Driver Grade 3 course is provided with a number of valuable handbooks. The handbooks include typical daily tasks, the procedures, emergency response tasks, nautical terminology, reference material and for student use only.
  • Reading of the handbooks is required and necessary to support your learning outcomes and help produce a better result in your assessment tasks; and the Maritime Authority Oral Assessment for your Marine Engine Driver Grade 3 Certificate of Competency.
  • 160 page SEA SCHOOL Fire and Safety Handbook.
  • 335 page SEA SCHOOL Engineering Handbook.
  • The Small Ships Manual, and the Australian Boating Manual by Dick Gandy are also suitable and recommended reference books for maritime career participants who continue with training and sea experience.
  • The SEA SCHOOL Course Handbooks for General Purpose Deckhand, Fight Fire, Master Class 5 are also fundamental to your wheelhouse library
  • In time, you will need your own engineering tools and multi-meter.

Maritime Application

The next step is to lodge your NSW Maritime Application for a Certificate of Competency as a Marine Engine Driver Grade 3. To apply you must also provide a resume, training certificates, documentation and evidence of sea service. Please refer to our Information section for more details.